FEATURES
• Unique performance-to-size ratio
• Asymmetrical horizontal and vertical coverage
• Stainless steel chassis
• Electronically protected
DESCRIPTION
– By combining the KX12 with active K-array subwoofers, three portable systems are created, which differ in size of the subwoofers and number of KX12 units used.
– With powered subwoofers that maintain the same digital editing features of all K-array active subwoofers, the KRX systems feature an integrated touch screen, providing intuitive control over the main DSP functions, such as input/output levels, signal routing, offset delays for subwoofer and mid-high speaker output (up to 12 ms each) and overall system delays (up to 330 ms). All DSP functions, including EQ, can also be controlled remotely via software through USB or RS485 (3 pin XLR). With the K-dante accessory, the systems can be used in a Dante network.
– The largest of the three stereo systems is the KRX802. With three KX12 speakers combined with a KMT218 subwoofer, the system converts into a line array that delivers maximum SPL, very low frequency and best bass response. No longer a point source, the KRX802 covers larger distances with higher pressure in larger venues by means of an extendable pole and proper joining and stacking hardware per side. Possible applications are DJ use, clubs and anywhere a lot of pressure is needed close to the speakers.
TECHNICAL SPECIFICATIONS
KX12
| ACOUSTICS | |
| Power handling | 800 + 200 W |
| Impedance | 8Ω |
| Frequency range | 120 Hz – 19 KHz (1) |
| Maximum SPL | 127 dB (cont.) – 133 dB (peak) (2) |
| COVERAGE | |
| Horizontal | 100°/30° (depending on horn orientation) |
| Vertical | 100°/30° (depending on horn orientation) |
| TRANSDUCERS | |
| Coaxial | 1 x 12” Neodymiun magnet woofer with 3” voice coil
Neodymium magnet compression driver with 2” voice coil |
| POWER AUDIO INPUT | |
| Connectors | s 2 x 4-pin Speakon |
| Wiring | 1+ 1- (Signal IN & LINK ) 2+ 2- (Through) |
| RECOMMENDED AMPLIFIERS | |
| Type | KMT18, KMT21, KMT218, KA84 |
| PHYSICAL | |
| Dimensions | 34.0 x 32.0 x 20.0 cm (13.4“ x 12.6” x 7.9“) |
| Weight | 12.2 kg (26.9 lbs) |
Notes for data
1. With dedicated preset;
2. Measured with musical signal New materials and design are introduced into existing products without previous notice.
Present systems may differ in some respects from those presented in this catalogue.
KMT218
| ACOUSTICS | |
| Power handling | 1600 W (AES) |
| Impedance | 4Ω |
| Frequency range 1 | 30 Hz – 150 Hz (1) |
| Maximum SPL | 134 dB (cont.) – 140 dB (peak) (2) |
| COVERAGE | |
| Horizontal | Omni |
| Vertical | Omni |
| CROSSOVER | |
| Type | DSP controlled |
| Frequency | Low pass @ 150 HZ (maximum – preset dependent) |
| TRANSDUCERS | |
| Type | 2 X 18” Neodymium magnet woofer with 3” voice coil |
| AMPLIFIERS | |
| Type | 1 module class D – DSP controlled |
| Subwoofer Power Output | 2500 W @ 4 Ω 1% THD + NOISE (3) |
| Speakon Power output | 2500 W @ 4 Ω 1% THD + NOISE (3) |
| Protections | Over Temp.(Power Limiting – Thermal Shutdown),
Short Circuit/ Overload Output Protection,Power Limiting, Clip Limiter/Permanent Signal Limiter, High Frequency Protection |
| PHYSICAL | |
| Dimensions | 95.3 cm x 48 cm x 60 cm (37.52“ x 19.9” x 23.62“) |
| Weight | 49 Kg (108.03 lb) |
Notes for data
1. With dedicated preset
2. Measured with musical signal
3. EIAJ Test Standard, 1KHz, 1%THD New materials and design are introduced into existing products without previous notice.
Present systems may differ in some respects from those presented in this catalogue.
