Axle-KRX802

FEATURES

• Unique performance-to-size ratio

• Asymmetrical horizontal and vertical coverage

• Stainless steel chassis

• Electronically protected

DESCRIPTION

– By combining the KX12 with active K-array subwoofers, three portable systems are created, which differ in size of the subwoofers and number of KX12 units used.

– With powered subwoofers that maintain the same digital editing features of all K-array active subwoofers, the KRX systems feature an integrated touch screen, providing intuitive control over the main DSP functions, such as input/output levels, signal routing, offset delays for subwoofer and mid-high speaker output (up to 12 ms each) and overall system delays (up to 330 ms). All DSP functions, including EQ, can also be controlled remotely via software through USB or RS485 (3 pin XLR). With the K-dante accessory, the systems can be used in a Dante network.

– The largest of the three stereo systems is the KRX802. With three KX12 speakers combined with a KMT218 subwoofer, the system converts into a line array that delivers maximum SPL, very low frequency and best bass response. No longer a point source, the KRX802 covers larger distances with higher pressure in larger venues by means of an extendable pole and proper joining and stacking hardware per side. Possible applications are DJ use, clubs and anywhere a lot of pressure is needed close to the speakers.

TECHNICAL SPECIFICATIONS

KX12

ACOUSTICS
Power handling 800 + 200 W
Impedance
Frequency range 120 Hz – 19 KHz (1)
Maximum SPL 127 dB (cont.) – 133 dB (peak) (2)
COVERAGE
Horizontal 100°/30° (depending on horn orientation)
Vertical 100°/30° (depending on horn orientation)
TRANSDUCERS
Coaxial 1 x 12” Neodymiun magnet woofer with 3” voice coil

Neodymium magnet compression driver with 2” voice coil

POWER AUDIO INPUT
Connectors s 2 x 4-pin Speakon
Wiring 1+ 1- (Signal IN & LINK ) 2+ 2- (Through)
RECOMMENDED AMPLIFIERS
Type KMT18, KMT21, KMT218, KA84
PHYSICAL
Dimensions 34.0 x 32.0 x 20.0 cm (13.4“ x 12.6” x 7.9“)
Weight 12.2 kg (26.9 lbs)

Notes for data

 1. With dedicated preset;

2. Measured with musical signal New materials and design are introduced into existing products without previous notice.

Present systems may differ in some respects from those presented in this catalogue.

KMT218

ACOUSTICS
Power handling 1600 W (AES)
Impedance
Frequency range 1 30 Hz – 150 Hz (1)
Maximum SPL 134 dB (cont.) – 140 dB (peak) (2)
COVERAGE
Horizontal Omni
Vertical Omni
CROSSOVER
Type DSP controlled
Frequency Low pass @ 150 HZ (maximum – preset dependent)
TRANSDUCERS
Type 2 X 18” Neodymium magnet woofer with 3” voice coil
AMPLIFIERS
Type 1 module class D – DSP controlled
Subwoofer Power Output 2500 W @ 4 Ω 1% THD + NOISE (3)
Speakon Power output 2500 W @ 4 Ω 1% THD + NOISE (3)
Protections Over Temp.(Power Limiting – Thermal Shutdown),

Short Circuit/ Overload Output Protection,Power Limiting,

Clip Limiter/Permanent Signal Limiter,

High Frequency Protection

PHYSICAL
Dimensions 95.3 cm x 48 cm x 60 cm (37.52“ x 19.9” x 23.62“)
Weight 49 Kg (108.03 lb)

Notes for data

1. With dedicated preset

2. Measured with musical signal

3. EIAJ Test Standard, 1KHz, 1%THD New materials and design are introduced into existing products without previous notice.

Present systems may differ in some respects from those presented in this catalogue.