FEATURES
• Self powered
• Integrated DSP with multiple analog and digital inputs
• Onboard touch screen with matrix control
• Direct radiating, long excursion 2 x 18” cone drivers
• RS485 and USB connectivity for remote control
• Fitted with integral handles
DESCRIPTION
• The K-array KMT218 is much more than a standard 2 x 18” powered subwoofer. The amplifier mounted on board is class D, delivering 2 x 2000 W at 4Ω. One of the two amplifying channels is dedicated to an output Speakon to connect to many kinds of speaker configurations, including single mid-high modules (KY102, KP52, KP102), multiple line arrays, or the passive version of an additional bass module (KMT218P, KMT18P or KMT21P). The rear panel provides input for a balanced line signal, a balanced microphone signal with phantom power, and digital signals in AES/EBU protocol, also on an XLR for ease of cabling. An integrated touch screen provides intuitive managing and editing of powerful DSP controlling:Input and output levels, In/Out routing,speakon output delay, subwoofer delay, overall system delay (up to 330 ms).
• All DSP functions, including EQ can be controlled with remote managing software via USB or RS485, again conveniently on a standard XLR. To optimize performance, the onboardDSP includes presets to drive K-array speakers. The chassis features large ports designed to be fully symmetrical to the speakers, which means the back loading on the drivers is consistent and even with no port air turbulence. This also gives incredible structural strength to the cabinet despite its light weight. Pocket handles and an M20 thread mount position for attaching mid-high speakers makes the KMT218 convenient to use and ideal for medium throw applications in theaters, concert halls, and Audio/Video installations.
• All KTM218 components are designed by the K-array R&D department and custom-made under the K-array quality control system.
TECHNICAL SPECIFICATIONS
| ACOUSTICS | |
| Speaker power handling | 1600 W |
| Max Power | 2800 W (1) |
| Impedance | 4 Ω |
| Frequency range | 30 Hz – 150 Hz ± 3dB (preset relating) |
| SPL 1W/1mt | 98 dB |
| Maximum SPL | 130 dB continuous – 136 dB peak |
| COVERAGE | |
| Horizontal | Omni |
| Vertical | Omni |
| CROSSOVER | |
| Type | DSP controlled |
| Frequency | 150 Hz (preset dependent) |
| TRANSDUCERS | |
| Full range | 1 x 21” Neodymium speakers with 3” voice coil |
| AUDIO IN/OUT | |
| Analog connectors | 2 male + 2 female 3-pin balanced XLR |
| Digital connectors | 1 male + 1 female 3-pin balanced XLR |
| AUDIO POWERED OUTPUT | |
| Connector | Female Speakon |
| Wiring | Pin1+= CH1+ Pin1= CH1- Pin2+= N.C. Pin2= N.C. |
| RECOMMENEND AMPLIFIERS | |
| Type | 1 male + 1 female XLR parallel / 1 USB B Jack serial converter |
| POWER INPUT | |
| Connectors https://cialisfromuk.com/generic-cialis-in-uk/ | 2 x PowerCon IN/OUT |
|
AMPLIFIER |
|
| Type | 1 module class D – DSP controlled |
| Subwoofer Power Output | 2400 Watt 1 @ 4Ω |
| Speakon Power output | 2400 Watt 1 @ 4Ω |
| Protections | Dynamic limiter, over current, over temp, short circuits |
|
AC POWER |
|
| Nominal power requirements | 100 – 240 Vac ± 10% 50-60 Hz |
| Operating Range | 85 – 265 Vac (auto-range) |
|
CONSUMPTION |
|
| 1/8 rated power (pink noise) @ 8Ω | 300 W |
| PHYSICAL | |
| Dimensions | 55.5 cm x 55.5 cm x 76.3 cm (21.9“ x 21.9” x 30.0“) |
| Weight | 49 kg (108 lbs) |
Notes for data
1. Amplifier wattage rating is based on the maximum unclipped burst sine wave RMS voltage that the amplifier will produce into the nominal load impedance. New materials and design are introduced into existing products without previous notice. Present systems may differ in some respects from those presented in this catalogue.
